[{"type":"paragraph","children":[{"t":"text","v":"Model File Release:","b":true,"i":false},{"t":"text","v":" SteinWipe_V3_Pro_Advanced_Edition.3mf","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Developed On:","b":true,"i":false},{"t":"text","v":" Bambu Lab P1 Series \/ X1C","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Released","b":true,"i":false},{"t":"text","v":": March 18 2026","b":false,"i":false}]},{"type":"heading","level":2,"children":[{"t":"text","v":"Overview","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"The P1\/X1 SteinWipe project V3 wiper mount: Pro Advanced Edition is the magnetic sliding bracket wiper system for the Bambu Lab P1 Series and X1C printers. Unlike the V1 and V2 wiper mounts which bolt directly to the printer\u0026#39;s rear panel, the V3 Pro Advanced splits the wiper into two parts: a magnetic base plate that bolts to the printer permanently, and a wiper slide assembly that drops into the base plate and locks in place magnetically. The wiper slide can be removed by hand for cleaning or service without unbolting anything, and the assembly returns to its calibrated position automatically when reinstalled.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"This manual covers printing the four printable parts, assembling the wiper, and installing it onto a backing plate that has already been mounted to your printer\u0026#39;s rear panel. Z height setup for both the wiper and ProTab is the most precise part of the install and gets its own detailed section.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"% SteinWipe Pro Advanced Edition","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"steinwipe_pro_advanced_hero | scale=100 | caption=bottom","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"The printed and fully assembled SteinWipe V3 Pro Advanced Edition.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"\/%","b":false,"i":false}]},{"type":"heading","level":2,"children":[{"t":"text","v":"Where this manual sits in the whole setup process","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"This is step 2 of 4 in a P1\/X1 SteinWipe install:","b":false,"i":false}]},{"type":"list","listType":"ordered","items":[{"children":[{"t":"text","v":"Drill the mounting holes and print the rear backing plate.","b":true,"i":false},{"t":"text","v":" Covered in the ","b":false,"i":false},{"t":"link","v":"SteinWipe Hole Template V3 and Rear Backing Plate V2 manual","url":"https:\/\/leckiestein.com\/pages\/swmc-releases\/stein-wipe-hole-template-v-3-and-rear-backing-plate-v-2","target":"_blank"},{"t":"text","v":". Complete this first - the V3 Pro Advanced bolts to the backing plate installed in that step.","b":false,"i":false}]},{"children":[{"t":"text","v":"Print and install your wiper mount.","b":true,"i":false},{"t":"text","v":" This manual.","b":false,"i":false}]},{"children":[{"t":"text","v":"Set up the SteinWipe Motion Control preset in your slicer.","b":true,"i":false},{"t":"text","v":" Covered in the ","b":false,"i":false},{"t":"link","v":"SWMC release listing for your printer and slicer combination.","url":"https:\/\/leckiestein.com\/collections\/steinwipe-core-releases-p1-x1-collection","target":"_blank"},{"t":"text","v":"","b":false,"i":false}]},{"children":[{"t":"text","v":"Calibrate your wiper offsets.","b":true,"i":false},{"t":"text","v":" Covered in the ","b":false,"i":false},{"t":"link","v":"V3 Wiper XY Offset Calibration manual","url":"https:\/\/leckiestein.com\/pages\/swmc-releases\/p-1-x-1-stein-wipe-v-3-0-wiper-offset-calibration","target":"_blank"},{"t":"text","v":".","b":false,"i":false}]}]},{"type":"paragraph","children":[{"t":"text","v":"If you have not yet completed step 1, stop here and complete the backing plate install first. The V3 Pro Advanced cannot be mounted without the backing plate behind the printer\u0026#39;s rear panel.","b":false,"i":false}]},{"type":"heading","level":2,"children":[{"t":"text","v":"A note on cleanliness before you begin","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"The wiper pad attaches to a printed pocket using an adhesion promoter at the end of this install. ","b":false,"i":false},{"t":"text","v":"The oils on your skin will degrade the bond if you touch the inside surface of that pocket during assembly.","b":true,"i":false},{"t":"text","v":" Treat the front face of the wiper slide pocket as a no-touch zone from this point forward. Handle the wiper slide by its edges or the outside surface during the entire build. A good option is to wear gloves. Do not install the wiper pad early incase something does not workout with the mount during the setup.","b":false,"i":false}]},{"type":"heading","level":2,"children":[{"t":"text","v":"1. What\u0026#39;s included","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"1.1 Printable parts","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Four parts ship in the V3 Pro Advanced .3mf:","b":false,"i":false}]},{"type":"list","listType":"unordered","items":[{"children":[{"t":"text","v":"Magnetic base plate.","b":true,"i":false},{"t":"text","v":" Bolts to the printer\u0026#39;s backing plate. Holds two N52 magnets that lock the wiper slide in place. Stays mounted permanently once installed.","b":false,"i":false}]},{"children":[{"t":"text","v":"Wiper slide.","b":true,"i":false},{"t":"text","v":" The removable part of the assembly. Holds the A1 wiper pad on its front face and slides into the magnetic base plate. Drops in and pulls out by hand once calibrated.","b":false,"i":false}]},{"children":[{"t":"text","v":"ProTab post mount.","b":true,"i":false},{"t":"text","v":" Slides into the wiper slide alongside the magnets. Holds the ProTab Contact in position and provides the Z height adjustment for the ProTab.","b":false,"i":false}]},{"children":[{"t":"text","v":"ProTab locking drawbar.","b":true,"i":false},{"t":"text","v":" Small key-shaped part that locks the ProTab post mount in place once Z height is set. Available in two colors at the leckiestein.com store: red drawbars are for laser-textured ProTab Contacts; gray drawbars are for smooth ProTab Contacts. Choose the color matching your tab finish.","b":false,"i":false}]}]},{"type":"heading","level":3,"children":[{"t":"text","v":"1.2 Hardware","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"All hardware for the wiper assembly is available at the ","b":false,"i":false},{"t":"link","v":"P1\/X1 SteinWipe Hardware Collection","url":"https:\/\/leckiestein.com\/collections\/p1-x1-steinwipe-mounts-hardware","target":""},{"t":"text","v":" on leckiestein.com. Source from one place, source everything.","b":false,"i":false}]},{"type":"list","listType":"unordered","items":[{"children":[{"t":"text","v":"Two 10x5x2 N52 magnets (Leckiestein magnets are listed as N32 but the supplier claims N52, downgrading the description in the listing until they can be verified) ","b":false,"i":false}]},{"children":[{"t":"text","v":"Three Leckiestein #1 Phillips M2.6 x 8mm wafer screws (two for the wiper slide height adjustment, one for the drawbar lock)","b":false,"i":false}]},{"children":[{"t":"text","v":"Two M3 x 6mm button head cap screws (mount the magnetic base plate to the backing plate)","b":false,"i":false}]},{"children":[{"t":"text","v":"One ProTab Contact (laser-textured or smooth)","b":false,"i":false}]},{"children":[{"t":"text","v":"One Bambu Lab A1 Series rubber wiper pad","b":false,"i":false}]},{"children":[{"t":"text","v":"Optional - adhesion promoter (used to bond the wiper pad to its pocket for install)","b":false,"i":false}]}]},{"type":"paragraph","children":[{"t":"text","v":"About the A1 wiper pad:","b":true,"i":false},{"t":"text","v":" the pad is the only component the user supplies separately if they print the wiper themselves due to limited supply from Bambu Lab for OEM pads. If you would rather skip printing entirely, the ","b":false,"i":false},{"t":"link","v":"SteinWipe V3 Pro Advanced Hardware Kit","url":"https:\/\/leckiestein.com\/products\/steinwipe-pro-printed-kit-advanced-edition?variant=47587796123799","target":"_blank"},{"t":"text","v":" ships fully assembled with the OEM Bambu Lab A1 pad installed and the entire wiper ready to mount.","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"1.3 Tools","b":false,"i":false}]},{"type":"list","listType":"unordered","items":[{"children":[{"t":"text","v":"#1 Phillips driver with a sharp tip (for the M2.6 x 8mm screws)","b":false,"i":false}]},{"children":[{"t":"text","v":"2.0mm allen key (for the M3 x 6mm screws holding the base plate)","b":false,"i":false}]},{"children":[{"t":"text","v":"A small flat blade screwdriver (for ejecting magnets from the base plate if needed; not used in normal install)","b":false,"i":false}]}]},{"type":"heading","level":2,"children":[{"t":"text","v":"2. Print the parts","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"2.1 Print profile and material","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Use the provided Bambu Studio .3mf print profile with heat dried PETG-HF. The profile is tuned for the V3 Pro Advanced\u0026#39;s tight-tolerance sliding components. Default speeds with default settings will not produce parts that slide cleanly into each other.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"BBL PETG-HF used during development is the only material validated for the magnetic bracket geometry and the sliding mechanism tolerances with the released profile. PLA will not hold up to the temperatures near the toolhead during AMS cycles and other PETG materials may need further tuning. For best results, dry your PETG-HF material at 65c for 24 hours in your AMS 2 Pro or other heated dryer. ","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Estimated total print time using the provided profile: approximately 2.5 hours.","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"2.2 Settings worth verifying if slicing the STLs directly","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"If you slice the STLs without using the provided profile, verify these settings:","b":false,"i":false}]},{"type":"list","listType":"unordered","items":[{"children":[{"t":"text","v":"No supports","b":false,"i":false}]},{"children":[{"t":"text","v":"No brim","b":false,"i":false}]},{"children":[{"t":"text","v":"No raft","b":false,"i":false}]},{"children":[{"t":"text","v":"Print-by-object enabled","b":false,"i":false}]},{"children":[{"t":"text","v":"Filament flow ratio tuned","b":false,"i":false}]},{"children":[{"t":"text","v":"Wall speeds should not exceed 60mm\/s","b":false,"i":false}]}]},{"type":"paragraph","children":[{"t":"text","v":"Print-by-object matters. Each part finishes completely before the next one starts, producing more consistent layer times within a single part. Travel moves between objects are gentler than between layers within an object, reducing the chance of one part being knocked loose.","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"2.3 Plate adhesion","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"PETG-HF on a clean textured PEI plate gives reliable adhesion at default plate temperature. If you are running a non-PEI plate, a light wipe with isopropyl alcohol before printing helps.","b":false,"i":false}]},{"type":"heading","level":2,"children":[{"t":"text","v":"3. Clean up and pre-fit the parts","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Before assembly, clean any strings or layer artifacts off the parts. Pay attention to the sliding surfaces in particular: the drawbar channel, the magnetic base plate\u0026#39;s slide rails, and the ProTab post mount\u0026#39;s sliding surface.","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"3.1 Test the sliding fits","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Three fits need to work cleanly before you can assemble the wiper:","b":false,"i":false}]},{"type":"list","listType":"ordered","items":[{"children":[{"t":"text","v":"Drawbar into the wiper slide groove","b":true,"i":false},{"t":"text","v":" (left side of the drawbar)","b":false,"i":false}]},{"children":[{"t":"text","v":"Drawbar into the ProTab post mount","b":true,"i":false},{"t":"text","v":" (right side of the drawbar)","b":false,"i":false}]},{"children":[{"t":"text","v":"Wiper slide into the magnetic base plate","b":true,"i":false}]}]},{"type":"paragraph","children":[{"t":"text","v":"Each fit should slide together with light hand pressure. If any of them bind or refuse to slide, you have two paths to resolve it.","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"3.2 Path A - work the parts together by hand","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"For mildly tight fits, slide the parts in and out of each other a dozen times. The friction lightly polishes the contact surfaces and the parts will start to move more freely. This handles most cases where the fit feels slightly tight but mostly works.","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"3.3 Path B - heat conform the parts on the print bed","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"If working the parts by hand doesn\u0026#39;t free them up, the parts need a heat conform pass.","b":false,"i":false}]},{"type":"list","listType":"unordered","items":[{"children":[{"t":"text","v":"Set your print bed to 70°C","b":false,"i":false}]},{"children":[{"t":"text","v":"Lay the two assembled parts face up on the bed","b":false,"i":false}]},{"children":[{"t":"text","v":"Leave them for 45 minutes and turn the bed heater off","b":false,"i":false}]},{"children":[{"t":"text","v":"Let them cool naturally on the bed for roughly 15 minutes with the printer door open","b":false,"i":false}]}]},{"type":"paragraph","children":[{"t":"text","v":"The plastic gets soft enough that the two parts will form to each other slightly, accommodating the small dimensional differences from the print. This is not hot enough to deform the parts past functionality - the bed temperature is below PETG-HF\u0026#39;s glass transition.","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"3.4 Path C - reduce flow ratio and reprint","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"If even heat conforming doesn\u0026#39;t get the parts to slide, your printer is over-extruding slightly and the contact wall thicknesses are coming out oversized. The fix is to reduce flow ratio.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Reducing flow ratio is preferred over scaling the model","b":true,"i":false},{"t":"text","v":" because flow ratio only changes wall thickness; it does not change hole positions or slide receptacle dimensions on the scale where those features matter. Scaling the model would shift the screw holes and the magnet pockets.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"% Flow ratio setting location","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"flow_ratio_setting_in_slicer | scale=100 | caption=bottom","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"The flow ratio setting in Bambu Studio filament profile. Reduce by 1-2% increments and reprint until the parts slide freely.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"\/%","b":false,"i":false}]},{"type":"heading","level":2,"children":[{"t":"text","v":"4. Assemble the wiper","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"4.1 Install the magnets into the base plate","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"The magnetic base plate has two pockets that receive the 10x5x2 N52 magnets. Press the magnets into the pockets fully; they should seat flush with the surrounding plastic on the right and sit deep within the pocket on the left. Use your 2mm hex key to install the left magnet.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Polarity does not matter.","b":true,"i":false},{"t":"text","v":" The magnets attract steel; they hold the wiper slide in position by pulling on the steel M2.6 screws installed in the wiper slide (next step). Either magnet orientation works equally well.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"% Magnets seated in base plate","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"magnets_seated_in_base_plate | scale=100 | caption=bottom","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Both magnets fully seated in the magnetic base plate pockets, flush with the plastic surface.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"\/%","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"If you ever need to remove the magnets later:","b":true,"i":false},{"t":"text","v":" the base plate has a window with a pie-slice opening at the center. Insert a small flat blade screwdriver into the window and twist - the magnets will eject without damage to either the magnets or the base plate.","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"4.2 Install the two height adjustment screws into the wiper slide","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"The wiper slide takes two M2.6 x 8mm Phillips screws. These screws serve two purposes: they provide the steel that the magnets pull against to lock the wiper slide into the base plate, AND they set the wiper slide\u0026#39;s height when installed.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Drive the screws in slowly and as straight as possible.","b":true,"i":false},{"t":"text","v":" Driving them in fast or at an angle will split the layers of the printed wiper slide because PETG-HF needs time to flex and accept the screw thread. If the room is cool (20C or less), setting your print bed to 40C and placing the wiper slide on the bed for 10 minutes before installing the screws will also help prevent cracking.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Note: Do not place the wiper slide or magnetic base on a 70C bed for and extended period of time after installing the screws or magnets to help with slide fitment mentioned above - this will cause the magnets and screws to become loose due to relieving the needed pressure in the openings.","b":true,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"% Layer splitting from fast screw install","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"wiper_slide_layer_split_damage | scale=70 | caption=bottom","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"What can happen if M2.6 screws are driven too fast or at an angle into the wiper slide. The layers separate and the screw no longer holds correctly.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"\/%","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Drive both screws in all the way in until the screw head just touches the surface of the wiper slide. Do not tighten further - a gentle snug is enough. The threads are formed in plastic; over-tightening strips them.","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"4.3 Setting the screw heights; asymmetric backout pattern","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"This is the most important part of the wiper geometry. With the 2 screws fully seated, we now need to back out the screws by different amounts, creating a slight angle across the wiper that compensates for variation in wiper pad nub dimension and spacing across different pads from different manufacturers.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"% OEM Wipers From Bambu Lab 2 years apart","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"oem_wiper_bbl_variation | scale=70 | caption=bottom","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"The wiper on the top was manufactured in 2026 and the wiper on the bottom was in 2024. Both wiper are OEM from Bambu Lab.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"\/%","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Why the angle exists:","b":true,"i":false},{"t":"text","v":" wiper pads from different production runs and different manufacturers vary by up to 1mm in overall length dimension and nub spacing. Even genuine Bambu Lab A1 pads from 2024 versus 2026 differ by close to a millimeter in overall length difference. Rather than writing special wipe cycles specific to each pad variation, the wiper mount itself is tilted slightly so the right side of the pad has more vertical room for any slight misalignment on the X axis. The nubs on the right can flex and bend without being sheared off by the nozzle on each pass. This matters for weaving cycles such as rake wipe cycles.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"The left side of the wiper sees the most nozzle engagement","b":true,"i":false},{"t":"text","v":" - this is where the XY calibration aligns the nozzle\u0026#39;s entry point, so the left side must match the calibrated XY position perfectly. The right side gets the wiggle room.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Backout procedure:","b":true,"i":false}]},{"type":"list","listType":"ordered","items":[{"children":[{"t":"text","v":"Position your eye so you can see the tip of the Phillips driver inside the screw head clearly. You will count quarter turns by watching the Phillips driver blades.","b":false,"i":false}]},{"children":[{"t":"text","v":"Left screw: back out exactly one full turn.","b":true,"i":false},{"t":"text","v":" That\u0026#39;s four quarter-turn steps.","b":false,"i":false}]},{"children":[{"t":"text","v":"Right screw: back out exactly 3\/4 of a turn.","b":true,"i":false},{"t":"text","v":" That\u0026#39;s three quarter-turn steps.","b":false,"i":false}]}]},{"type":"paragraph","children":[{"t":"text","v":"After this, the left side of the wiper will sit slightly higher than the right. ","b":false,"i":false},{"t":"text","v":"This is correct.","b":true,"i":false},{"t":"text","v":" Do not \u0026quot;level\u0026quot; the wiper - the asymmetry is intentional.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"% Counting quarter turns","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"counting_quarter_turns_phillips | scale=45 | caption=bottom","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Watch the tip of the Phillips driver inside the screw head to count quarter turns accurately. Position your eye over the screw head and look down the closest of the 4 phillips tip blades. Hold your and and eye in this position while you step the screw out by 1\/4 turns marking each new quarter turn blade position when it matches the initial noted position. ","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"\/%","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"4.4 Check for play in the wiper slide","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Slide the wiper slide into the magnetic base plate. The magnets will engage and pull the assembly into position.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Test for play by gently lifting the wiper slide:","b":false,"i":false}]},{"type":"list","listType":"unordered","items":[{"children":[{"t":"text","v":"Left side:","b":true,"i":false},{"t":"text","v":" should have essentially zero play. The magnet engagement on the left holds the slide firmly down.","b":false,"i":false}]},{"children":[{"t":"text","v":"Right side:","b":true,"i":false},{"t":"text","v":" may have a small amount of play when lifting up. This is acceptable.","b":false,"i":false}]}]},{"type":"paragraph","children":[{"t":"text","v":"The wiper is designed to handle 600g of downward force when the nozzle docks on the ProTab. The left side must not lift under that force causing any teetering which will lead to wear and noise. If the left side has any noticeable upward play, the height adjustment screws likely weren\u0026#39;t driven in fully from the start or not backed out to the mentioned positions. Small variations may also occur in printing creating a need for additional adjustment. Aside from setting the correct height for the wiper, the goal is to ensure the wiper slide does not rock when the nozzle docks on the tab.","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"4.5 Install the drawbar into the ProTab post mount","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"The drawbar has a 45-degree flat on one side; the ProTab post mount has a matching 45-degree flat. ","b":false,"i":false},{"t":"text","v":"These must match before the drawbar slides in.","b":true,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Once the drawbar clips into place, it is very difficult to remove without damaging the post mount. Verify the orientation before committing to the slide-in.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"% Drawbar and post mount orientation","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"drawbar_post_mount_orientation | scale=100 | caption=bottom","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"The 45-degree flat on the drawbar (right) aligned with the matching flat on the ProTab post mount (left). The flats must align before the drawbar slides in. Some flexing of the wings of the post mount is needed to get the drawbar installed. Suggested to print the drawbar in red if you plan to install a SteinWipe laser textured control tab to match the color code of the official product.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"\/%","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"4.6 Install the ProTab Contact into the post mount","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Slide the ProTab Contact into the post mount channel by hand to start it. Then use a flat blade screwdriver to push it down until it seats.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Do not seat the ProTab too deep.","b":true,"i":false},{"t":"text","v":" The pocket is intentionally deeper than the tab needs - about 1mm of extra depth - to accommodate variation in ProTab Contact dimensions across manufacturers. If you push the tab too deep, the plastic housing pushes up on the tab from below the bend and deforms it causing the tab to be higher than it should and also reducing the space needed for the tab to compress which can apply too much pressure to the nozzle.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"The correct seating position: ","b":false,"i":false},{"t":"text","v":"the bend in the ProTab should sit flush with the surface where the drawbar slides through the post mount.","b":true,"i":false},{"t":"text","v":" That surface is the reference; the bend in the tab lines up with it.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"% ProTab seated correctly","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"protab_seated_in_post_mount | scale=50 | caption=bottom","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"The ProTab Contact properly seated in the post mount, with the bend in the tab flush with the drawbar channel surface. Press the ProTab into place with a flathead to ensure you do not install the tab too deep into the pocket.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"\/%","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"4.7 Slide the post mount and drawbar into the wiper slide","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"With the drawbar installed in the post mount, slide the entire post-mount-plus-drawbar assembly into the channel on the wiper slide. This holds all the parts together while you install the last screw.","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"4.8 Install the drawbar lock screw (loosely for now)","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Install the third M2.6 x 8mm Phillips screw into the drawbar lock position. Drive it in only until the head of the screw barely touches the surface beneath it. ","b":false,"i":false},{"t":"text","v":"Do not tighten this screw yet.","b":true,"i":false},{"t":"text","v":" It needs to allow the ProTab post mount to slide up and down for Z height adjustment in the next section.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"After this screw is in place, the ProTab post mount should still slide up and down freely with light hand pressure. If it doesn\u0026#39;t, back the screw out slightly by roughly 1\/8th turns checking if it has freed up every 1\/8th turn.","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"4.9 Attach the A1 wiper pad to the wiper slide","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"If the wiper mount is looking promising for install e.g. it fits nicely into the magnetic base and it did not crack during the screw install - then the wiper pad can be installed to the mount. This is the only step where the wiper pad pocket gets touched with chemical promoter.","b":false,"i":false}]},{"type":"list","listType":"ordered","items":[{"children":[{"t":"text","v":"Apply adhesion promoter to the inside of the wiper pad pocket on the wiper slide. Follow the directions on the bottle - typically a thin even coat that can be applied with a syringe or Q-tip, then a brief drying period as per the product instructions.","b":false,"i":false}]},{"children":[{"t":"text","v":"Identify the front and back of the A1 wiper pad. The ","b":false,"i":false},{"t":"text","v":"front side has a larger corner radius than the back side.","b":true,"i":false},{"t":"text","v":" The front face is what the nozzle sees.","b":false,"i":false}]},{"children":[{"t":"text","v":"Position the wiper pad as far to the ","b":false,"i":false},{"t":"text","v":"left","b":true,"i":false},{"t":"text","v":" of the pocket as possible before pressing down. Once in place, press it down to lock it in working from left to right, keeping the pad inside the pocket boundaries.","b":false,"i":false}]},{"children":[{"t":"text","v":"For some pads, expect about 1mm of gap on the right end of the pocket.","b":true,"i":false},{"t":"text","v":" This is gap is intentional as mentioned in Section 4.3 - the right side has space to accommodate pad length variations.","b":false,"i":false}]}]},{"type":"paragraph","children":[{"t":"text","v":"% Wiper pad installed with left alignment","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"wiper_pad_installed_left_aligned | scale=45 | caption=bottom","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"The A1 wiper pad pressed into the pocket, aligned hard against the left edge. About 1mm of gap is visible at the right end - this is correct.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"\/%","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"The wiper slide assembly is now complete. Set it aside while you mount the magnetic base plate to the printer.","b":false,"i":false}]},{"type":"heading","level":2,"children":[{"t":"text","v":"5. Mount the magnetic base plate","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"The magnetic base plate bolts to the backing plate you installed during step 1 (the Hole Template manual) or reuses the previous install holes and backing plate from the original V1 wiper mount install from 2024. The mounting hole pattern is the same.","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"5.1 Verify the backing plate is installed","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Confirm the rear backing plate is installed with the single M3 x 5mm BHCS center screw seated, as covered in the ","b":false,"i":false},{"t":"link","v":"Hole Template V3 and Rear Backing Plate V2 manual","url":"https:\/\/leckiestein.com\/pages\/project-documentation\/manual-steinwipe-hole-template-v-3-rear-backing-plate-v-2","target":"_blank"},{"t":"text","v":". The two outer holes should be clear and ready to receive the magnetic base plate screws. Note: The center screw holding the backing plate in place MUST be a button head cap screw and not a socket head cap screw otherwise the screw will prevent the magnetic base from sitting correctly.","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"5.2 Bolt the base plate to the printer","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Hold the magnetic base plate against the rear panel, aligning its two mounting holes with the two outer drilled holes. On the rear printer panel, the backing plate center hole should already have a M3 button head cap screw installed - this will help locate the two outer holes through the base plate. Pass two M3 x 6mm button head cap screws through the base plate and thread them into the backing plate\u0026#39;s outer nut pockets.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Tighten with a 2.0mm allen key until snug. Do not overtighten - the base plate is printed plastic and can deform under excessive torque when the printer chamber heats.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"% The Center BHCS Helps To Align The Base Plate","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"mag_base_plate_position_locator | scale=45 | caption=bottom","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"A button head cap screw already is installed in the center hole and holds the backing plate in place behind the rear panel of the printer. This screw is also used to help locate the outside holes through the base plate when placing the base plate into position.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"\/%","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"% Magnetic base plate installed","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"mag_base_plate_installed_on_printer | scale=45 | caption=bottom","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"The magnetic base plate bolted to the rear panel via the two outer screws on the backing plate.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"\/%","b":false,"i":false}]},{"type":"heading","level":2,"children":[{"t":"text","v":"6. Z height setup","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"This is where the install gets precise. The wiper height and the ProTab height both need to be set correctly before the wiper can do its job. Both heights are set mechanically using the screws you installed earlier as adjustable stops.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Reference point for all height work:","b":true,"i":false},{"t":"text","v":" the nozzle tip when the toolhead is positioned manually in front of the wiper, with the printer powered off.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Setting the Z height process is sequential. Wiper height first, then ProTab height. Do not skip ahead - the ProTab height check depends on the wiper being at the correct height first.","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"6.1 Position the toolhead manually","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"With the printer powered off, slide the wiper slide assembly into the magnetic base plate. Then manually move the toolhead by hand to a position ","b":false,"i":false},{"t":"text","v":"in front of the wiper, slightly to the left side, with the nozzle tip just about touching the wiper pad nubs.","b":true,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"% Toolhead positioned for wiper height check","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"toolhead_position_for_wiper_height_check | scale=45 | caption=bottom","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Manual toolhead position for wiper height check. The nozzle sits in front of the wiper, on the left side, with the widest part of the nozzle nearly touching the wiper nub tops.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"\/%","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"6.2 Check the wiper height","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"With the assembly in the lowest position (which it will be when you first install it on the magnetic base plate), the wiper should be ","b":false,"i":false},{"t":"text","v":"approximately 0.5mm too low","b":true,"i":false},{"t":"text","v":" for correct nozzle engagement. Most users will need to raise the wiper 0.5mm to 1.0mm for correct engagement. Note: the lowest install position varies slightly from printer to printer due to manufacturing tolerances in the printer itself; ","b":false,"i":false},{"t":"text","v":"procedure 6.3","b":true,"i":false},{"t":"text","v":" below adjusts the wiper to suit your specific machine.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Target wiper height:","b":true,"i":false},{"t":"text","v":" the tops of the wiper nubs should sit about 0.5mm short of the rubber sock that wraps around the bottom of the nozzle\/hotend. You can use the gap between wiper nubs as a reference since the spacing between nubs is about 0.5 - 0.7mm.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"% Correct wiper height","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"correct_wiper_height_reference | scale=65 | caption=bottom","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"What correct wiper height looks like. The wiper pad nubs sit about 0.5mm short of the nozzle\u0026#39;s rubber sock. Note: Do not position the wiper nubs higher than stated - during proper operation with high speed wiper toolpaths, the wiper nubs deform as the nozzle passes through and the maximum height of the nubs while deformed will be 0.5mm higher than the static position seen here. Setting the wiper too high will cause binding and premature wiper wear.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"\/%","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"This 0.5mm offset matches the V1 wiper\u0026#39;s correct engagement height that has been tested by thousands of users, so users coming from V1 will be in familiar territory. ","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"6.3 Adjust wiper height (if needed)","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"If the wiper is too low and needs to rise:","b":false,"i":false}]},{"type":"list","listType":"ordered","items":[{"children":[{"t":"text","v":"Manually move the toolhead out of the way.","b":false,"i":false}]},{"children":[{"t":"text","v":"Pull the wiper slide out of the magnetic base plate by hand.","b":false,"i":false}]},{"children":[{"t":"text","v":"Estimate the lift needed. Each quarter turn of the M2.6 screws = 0.25mm of lift. If the wiper needs to rise 0.5mm, both screws need to come out by 0.5mm worth of turns.","b":false,"i":false}]},{"children":[{"t":"text","v":"Back out the left screw first.","b":true,"i":false},{"t":"text","v":" For 0.5mm of lift, that\u0026#39;s two quarter turns (1\/2 turn total).","b":false,"i":false}]},{"children":[{"t":"text","v":"Back out the right screw by the same amount.","b":true,"i":false},{"t":"text","v":" Same two quarter turns.","b":false,"i":false}]},{"children":[{"t":"text","v":"Slide the wiper back into the base plate.","b":false,"i":false}]},{"children":[{"t":"text","v":"Manually reposition the toolhead and check the height.","b":false,"i":false}]}]},{"type":"paragraph","children":[{"t":"text","v":"Repeat until the height is correct. ","b":false,"i":false},{"t":"text","v":"The asymmetry from Section 4.3 must be preserved through every adjustment.","b":true,"i":false},{"t":"text","v":" Both screws move together by the same number of turns. If the left screw came out one full turn at the start and the right screw came out 3\/4 of a turn, that 1\/4 turn relative difference must remain across all adjustments. Adjusting one screw without adjusting the other will break the angle and change the wiper geometry.","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"6.4 Set the ProTab Z height","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Once the wiper height is set correctly, the ProTab height comes next.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Pre-tighten the drawbar lock screw slightly","b":true,"i":false},{"t":"text","v":" before this step. Turn it about 1\/8 to 1\/4 turn from its barely-touching position. The post mount should still slide within the wiper slide with light force but not drop out on its own under gravity.","b":false,"i":false}]},{"type":"list","listType":"ordered","items":[{"children":[{"t":"text","v":"Slide the wiper slide assembly into the magnetic base plate.","b":false,"i":false}]},{"children":[{"t":"text","v":"Manually position the toolhead so ","b":false,"i":false},{"t":"text","v":"the nozzle tip is centered horizontally on the arch in the ProTab Contact.","b":true,"i":false},{"t":"text","v":" The nozzle does not physically touch the tab in this step - it\u0026#39;s only a visual reference point.","b":false,"i":false}]},{"children":[{"t":"text","v":"Slide the ProTab post mount up or down within the wiper slide until ","b":false,"i":false},{"t":"text","v":"the topmost part of the ProTab arch sits about 0.5mm above the lowest point of the nozzle tip.","b":true,"i":false}]}]},{"type":"paragraph","children":[{"t":"text","v":"% Toolhead positioned for ProTab height check\ntoolhead_position_for_protab_height_check | scale=45 | caption=bottom\nManual toolhead position for ProTab height check. The nozzle tip aligns with the arch in the ProTab; no physical contact.\n\/%","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"The goal: when the toolhead docks on the ProTab during a print, the nozzle will engage the ProTab with about 0.5mm of compression. That compression provides clean electrical contact during AMS operations.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"% Correct ProTab height","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"correct_protab_height_reference | scale=65 | caption=bottom","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"What correct ProTab height looks like. The top of the ProTab arch sits 0.5mm above the nozzle tip, providing 0.5mm of dock compression.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"\/%","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"6.5 Lock the ProTab height with the drawbar screw","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"This is the most delicate step.","b":false,"i":false}]},{"type":"list","listType":"ordered","items":[{"children":[{"t":"text","v":"Without shifting the ProTab post mount out of position after being set, manually move the toolhead out of the way.","b":false,"i":false}]},{"children":[{"t":"text","v":"Carefully","b":true,"i":false},{"t":"text","v":" pull the wiper slide out of the magnetic base plate. The goal is to remove the slide without bumping the ProTab post mount and changing its height.","b":false,"i":false}]},{"children":[{"t":"text","v":"Look at the wiper slide from below (seen the the photo below). There will be a small gap visible between the drawbar and the ProTab post mount controlled by the drawbar screw.","b":false,"i":false}]},{"children":[{"t":"text","v":"Tighten the drawbar lock screw until that gap closes. ","b":false,"i":false},{"t":"text","v":"Closing the gap is all you need.","b":true,"i":false},{"t":"text","v":" Once it closes, stop turning.","b":false,"i":false}]}]},{"type":"paragraph","children":[{"t":"text","v":"Do not overtighten the drawbar lock screw. Closing the gap locks the post mount in position; tightening further only risks stripping the M2.6 thread in plastic or splitting the drawbar.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"% Closing the drawbar gap","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"closing_drawbar_lock_gap | scale=45 | caption=bottom","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"The gap between the drawbar and ProTab post mount visible from below. Tighten the drawbar lock screw only until this gap closes.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"\/%","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"6.6 Verify the ProTab height","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Slide the wiper assembly back into the magnetic base plate. Manually reposition the toolhead and confirm the ProTab still sits 0.5mm above the nozzle tip.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"If the height shifted during the lock step (most often from bumping the post mount when removing the slide), loosen the drawbar lock screw, reset the ProTab post mount position, and repeat Section 6.5.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"The control tab height is now mechanically set.","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"6.7 Check with pressure on the ProTab ","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"A final check to ensure the screws that set the height for the wiper are set correctly, apply downward pressure with your finger directly to the ProTab with enough force to compress the tab by about 1mm. There should be no play or rocking felt - the left side of the wiper mount should not lift.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"If you are feeling some rocking (teetering) seeing the left side of the wiper lifting slightly when applying down pressure to the tab, the right side height set screw is too high. Remove the wiper slide and turn the right screw in by an 1\/8 turn and retest. Repeat until the rocking is resolved. If there is rocking still after turning the screw until the screw is seated and can not be turned in any further, there is something obstructing the wiper slide preventing it from seating correctly.","b":false,"i":false}]},{"type":"heading","level":2,"children":[{"t":"text","v":"7. Next steps","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"7.1 Install the SteinWipe Motion Control preset","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Your wiper is installed mechanically, but it doesn\u0026#39;t do anything until the SteinWipe Motion Control preset is loaded into your slicer. This provides all the Gcode and logic needed to use the wiper and control tab. Find the latest SWMC Pro preset release matching your printer (P1 Series or X1C) and slicer (Bambu Studio or Orca Slicer) and follow the setup manual published on the release page. Make sure to add the SSD to the notes section to enable V3 wiper configuration.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Declares that SteinWipe Pro hardware is installed.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"{{\u0026gt;steinwipe_pro_installed}}","b":false,"i":false}]},{"type":"heading","level":3,"children":[{"t":"text","v":"7.2 Calibrate XY offsets","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"Once SWMC is installed in your slicer, run the V3 XY Offset Calibration. The calibration aligns the nozzle\u0026#39;s path through the wiper pad with sub-millimeter precision. Follow the ","b":false,"i":false},{"t":"link","v":"V3 Wiper XY Offset Calibration manual","url":"https:\/\/leckiestein.com\/pages\/project-documentation\/manual-steinwipe-wiper-offsets-and-general-calibration","target":""},{"t":"text","v":" for the full procedure.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"XY calibration is required before the first wipe cycle.","b":true,"i":false},{"t":"text","v":" If the XY offset is off by more than 0.5mm on a new install, the first wipe can rip the wiper pad. Do not skip this step.","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"After XY calibration is complete, the wiper assembly is fully calibrated and ready for use. A properly calibrated wiper should last thousands of wipe cycles. Future removals and reinstallations of the wiper slide will return to the same XY position automatically - no recalibration needed after cleaning or service.","b":false,"i":false}]},{"type":"heading","level":2,"children":[{"t":"text","v":"8. Notes","b":false,"i":false}]},{"type":"list","listType":"unordered","items":[{"children":[{"t":"text","v":"The asymmetric backout pattern (left screw 1 full turn, right screw 3\/4 turn) must be preserved through all height adjustments. Always adjust both screws by the same number of additional turns.","b":false,"i":false}]},{"children":[{"t":"text","v":"The wiper pad has a 1mm gap on the right side of its pocket. This is intentional; do not push the pad over to fill it. The gap accommodates pad-to-pad variation.","b":false,"i":false}]},{"children":[{"t":"text","v":"The 0.5mm baseline below correct engagement height matches V1 hardware. Users upgrading from V1 will recognize the calibration target.","b":false,"i":false}]},{"children":[{"t":"text","v":"After the install is complete and XY calibrated, the wiper slide can be pulled out by hand for cleaning or pad replacement. The magnetic base plate stays bolted to the printer and the slide returns to position automatically.","b":false,"i":false}]},{"children":[{"t":"text","v":"Drawbar color identification: red drawbars match laser-textured ProTab Contacts; gray drawbars match smooth ProTab Contacts. Make sure the drawbar in your kit matches your ProTab Contact finish.","b":false,"i":false}]}]},{"type":"heading","level":2,"children":[{"t":"text","v":"9. Known issues","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"None reported at release. Issues should be posted in the Leckiestein Discord #steinwipe channel.","b":false,"i":false}]},{"type":"heading","level":2,"children":[{"t":"text","v":"10. Terms and Conditions","b":false,"i":false}]},{"type":"paragraph","children":[{"t":"text","v":"By downloading and using these files, you agree to the ","b":false,"i":false},{"t":"link","v":"Leckiestein Terms of Service","url":"https:\/\/leckiestein.com\/policies\/terms-of-service","target":""},{"t":"text","v":".","b":false,"i":false}]}]

[{"base":"steinwipe_pro_advanced_hero","url":"https:\/\/leckiestein.com\/cdn\/shop\/files\/steinwipe_pro_advanced_hero.jpg?v=1780613737\u0026width=2400","width":1800,"height":1000},{"base":"flow_ratio_setting_in_slicer","url":"https:\/\/leckiestein.com\/cdn\/shop\/files\/flow_ratio_setting_in_slicer.png?v=1780616733\u0026width=2400","width":2474,"height":998},{"base":"magnets_seated_in_base_plate","url":"https:\/\/leckiestein.com\/cdn\/shop\/files\/magnets_seated_in_base_plate.jpg?v=1780617217\u0026width=2400","width":2742,"height":1124},{"base":"wiper_slide_layer_split_damage","url":"https:\/\/leckiestein.com\/cdn\/shop\/files\/wiper_slide_layer_split_damage.jpg?v=1780618007\u0026width=2400","width":1393,"height":760},{"base":"oem_wiper_bbl_variation","url":"https:\/\/leckiestein.com\/cdn\/shop\/files\/oem_wiper_bbl_variation.jpg?v=1780618965\u0026width=2400","width":1836,"height":757},{"base":"counting_quarter_turns_phillips","url":"https:\/\/leckiestein.com\/cdn\/shop\/files\/counting_quarter_turns_phillips.jpg?v=1780621797\u0026width=2400","width":1665,"height":1190},{"base":"drawbar_post_mount_orientation","url":"https:\/\/leckiestein.com\/cdn\/shop\/files\/drawbar_post_mount_orientation.jpg?v=1780622834\u0026width=2400","width":2763,"height":1072},{"base":"protab_seated_in_post_mount","url":"https:\/\/leckiestein.com\/cdn\/shop\/files\/protab_seated_in_post_mount.jpg?v=1780623309\u0026width=2400","width":1445,"height":1035},{"base":"wiper_pad_installed_left_aligned","url":"https:\/\/leckiestein.com\/cdn\/shop\/files\/wiper_pad_installed_left_aligned.jpg?v=1780624284\u0026width=2400","width":2030,"height":1258},{"base":"mag_base_plate_position_locator","url":"https:\/\/leckiestein.com\/cdn\/shop\/files\/mag_base_plate_position_locator.jpg?v=1780668787\u0026width=2400","width":2531,"height":1519},{"base":"mag_base_plate_installed_on_printer","url":"https:\/\/leckiestein.com\/cdn\/shop\/files\/mag_base_plate_installed_on_printer.jpg?v=1780668937\u0026width=2400","width":2549,"height":1434},{"base":"toolhead_position_for_wiper_height_check","url":"https:\/\/leckiestein.com\/cdn\/shop\/files\/toolhead_position_for_wiper_height_check.jpg?v=1780670003\u0026width=2400","width":2326,"height":1308},{"base":"correct_wiper_height_reference","url":"https:\/\/leckiestein.com\/cdn\/shop\/files\/correct_wiper_height_reference.jpg?v=1780670182\u0026width=2400","width":1100,"height":879},{"base":"correct_protab_height_reference","url":"https:\/\/leckiestein.com\/cdn\/shop\/files\/correct_protab_height_reference.jpg?v=1780671538\u0026width=2400","width":2304,"height":1296},{"base":"toolhead_position_for_protab_height_check","url":"https:\/\/leckiestein.com\/cdn\/shop\/files\/toolhead_position_for_protab_height_check.jpg?v=1780671899\u0026width=2400","width":2048,"height":1152},{"base":"closing_drawbar_lock_gap","url":"https:\/\/leckiestein.com\/cdn\/shop\/files\/closing_drawbar_lock_gap.jpg?v=1780672542\u0026width=2400","width":2346,"height":1320}]